Turbo Kit for Chevrolet Camaro (2010-2011) 3.6L

Complete twin-turbo intercooled package for the Chevrolet Camaro (2010–2011) with the 3.6L V6. It pairs two V6-specific stainless tubular manifolds with two T3/T4 hybrid turbos, dual internal wastegates, a front-mount intercooler, dual oiling kits, boost controller, blow-off valve, turbo timer, battery relocation, boost gauge and fuel-system parts in one box. Most installs keep A/C and power steering. On a stock motor, plan on a low-boost street tune around 8–10 psi. Big twin HP numbers are a hardware ceiling with a built engine and supporting mods, not a dyno result for a stock Camaro.

Why this kit

• Twin T3/T4 hybrid turbos with .57 trim compressors and .50 / .63 A/R housings
• V6-specific 321 stainless tubular manifolds with 1-5/8" primaries and V-band adapters
• Dual internal wastegates, dual oiling kits and front-mount intercooler
• Boost controller, blow-off valve, turbo timer, battery relocation and boost gauge included

Package Includes

• (2) T3/T4 hybrid turbochargers with oil fitting gaskets and mounting studs
• (2) V6 stainless steel turbo manifolds, TIG-welded 321, 1-5/8" primaries, with stainless V-band clamps and T3 V-band adapters
• (1) Front-mount aluminum intercooler
• (1) Aluminum intercooler piping kit: (2) 2.5" straight pipes, (2) 90°, (2) 60°, (2) 45° bends, (2) 2.5" 90° silicone couplers, (6) 2.5" straight silicone couplers, (16) stainless worm-gear clamps
• (2) Turbo oil line kits: high-strength feed lines, high-temp 550 psi returns, fittings, gaskets and hardware
• (2) Internal wastegate kits with flanges and clamps
• (1) Manual boost controller with install kit
• (1) Blow-off valve kit with install kit
• (1) Battery relocation kit, full aluminum, cables, straps and hardware
• (1) Slim reversible cooling fan
• (1) Electronic turbo timer with LED display and wiring
• (1) Adjustable fuel pressure regulator with gauge plus -6AN billet aluminum fuel filter
• (1) Oil catch can with install kit
• (1) Heat wrap roll
• (1) Boost gauge, 52 mm, backlit
• (2) High-flow washable air filters

Turbocharger Specs

• Type: T3/T4 hybrid each, wet-float bearings, balanced
• Compressor: .57 trim wheel, .50 A/R housing, 3" inlet, 2" outlet
• Turbine: .63 A/R housing via V-band to T3 adapters
• Oil inlet: 1/8" NPT
• About +power at 8–10 psi on a healthy stock motor with a proper tune; hardware ceiling over 450 hp per turbo with a built engine and supporting mods — not a stock-car dyno result

Exact Fitment — Chevrolet Camaro

• 2010–2011 Chevrolet Camaro with the 3.6L V6
• Not for V8 Camaros or 2012+ — verify engine before ordering
• Chassis-specific downpipes and exhaust beyond the turbo flanges are not included
• Intercooler piping is universal and needs cutting and fitting per chassis

Not Included

• Chassis-specific downpipes and exhaust beyond the turbo flanges
• Larger injectors, fuel pump and ECU tune (required)
• Clutch upgrade and wideband
• Oil-pan return bung if your setup needs one

Installation Notes

• Professional installation strongly recommended. Expect cutting and fitting of the universal piping
• The manifolds are V6-specific stainless tubular with V-band turbo adapters for clocking
• Oil return must drain by gravity on both turbos; prime each turbo with oil before first start and check for leaks
• Blow-off valve flanges are installed at your discretion
• Keep boost near 8–10 psi until fuel and tune are upgraded, and let the turbo timer handle cool-down

FAQs

Does this fit a V8 Camaro? No. This listing is 2010–2011 3.6L V6 only.

How much power will it make? A healthy stock engine at about 8–10 psi with a proper tune is the street baseline. Twin hardware can support far more with a built engine and full supporting mods.

Can I keep A/C and power steering? Most installs keep both; confirm clearance during mock-up.

Manual or automatic? Fits either when the engine matches.

Is it plug-and-play? No. You still need injectors, a fuel pump, an ECU tune, downpipes and some pipe fitting.