O2 Oxygen Sensor Upstream Downstream for Toyota Sienna (2007-2010) 3.5L
Couldn't load pickup availability
- Guaranteed Fitment
- Free Shipping, Lower 48 States
- Lifetime Warranty
Want it soon? Order within
Shop safely
Secure checkout with trusted payment providers.
Direct-Fit Upstream & Downstream O2 Oxygen Sensor Kit for 2007-2010 Toyota Sienna (XL20)
What it Does: The Direct-Fit 4-Piece Oxygen Sensor Kit for the 2007-2010 Toyota Sienna (XL20) with the 2GR-FE 3.5L V6 monitors pre- and post-catalytic exhaust oxygen content so the ECM can maintain stoichiometric fuel trim and verify converter efficiency.
The Stock Toyota Sienna Oxygen Sensor Failure
On the XL20 Sienna powered by the 2GR-FE 3.5L V6, factory upstream air-fuel ratio sensors and downstream narrowband oxygen sensors endure continuous thermal cycling and exhaust soot exposure. Over time, internal platinum-zirconia sensing elements become contaminated by fuel additives or oil vapor, while internal heater circuits suffer fatigue from repeated heat soak. This degradation causes sluggish switching response and biased voltage signals, frequently triggering P0135, P0155, P2195, or P0420/P0430 fault codes and forcing open-loop enrichment.
Common Symptoms of a Failing OEM Oxygen Sensor
- Check Engine Light / DTCs: Stored heater circuit or slow-response fault codes such as P0135, P0155, P0138, or biased P0420/P0430 converter efficiency codes.
- Sluggish Response & Hesitation: Skewed upstream air-fuel readings cause rough idle, throttle hesitation, and erratic short-term fuel trims across Bank 1 and Bank 2.
- Fuel Economy Drop & Failed Emissions: Forced open-loop enrichment increases fuel consumption and prevents OBD-II readiness monitors from completing during emissions inspections.
The Direct-Fit Oxygen Sensor Solution
This complete four-sensor kit replaces both upstream pre-cat sensors and both downstream post-cat heated sensors simultaneously to restore balanced bank-to-bank telemetry. Built with fast-acting ceramic sensing elements, corrosion-resistant stainless steel housings, and factory-matched wiring harnesses, every unit interfaces directly with the 2GR-FE ECM without splicing. Pre-terminated OEM-style connectors ensure positive locking engagement, while direct-thread bodies install cleanly into existing exhaust bungs to re-establish accurate closed-loop fuel control.
What's Included
- 2 Upstream Oxygen Sensors (Pre-Catalytic Converter)
- 2 Downstream Oxygen Sensors (Post-Catalytic Converter)
Technical Specifications
| Fitment | 2007-2010 Toyota Sienna |
|---|---|
| Engine / Chassis | 2GR-FE 3.5L V6 / XL20 |
| Sensor Configuration | 2 Upstream & 2 Downstream Direct-Fit Heated O2 |
| Installation Type | Direct Bolt-On OEM Replacement (No Cutting or Welding) |
| Replaces OEM Part # | 234-9012, 234-4149, 234-4516, 234-9049 |
Compatibility
- 2007-2010 Toyota Sienna 3.5L (XL20) — Upstream & Downstream Positions (Confirm engine displacement, model year, and connector style before ordering)
Frequently Asked Questions & Fitment Warnings
Does this fit the XL20 Sienna?
Yes. This is a direct fit for the 2007-2010 Toyota Sienna equipped with the 2GR-FE 3.5L V6 engine. It does not fit 2004-2006 XL20 models with the 3.3L 3MZ-FE engine or 2011+ models; always verify connector style and engine displacement prior to ordering.
Will replacing all four sensors clear P0420/P0430 or O2 heater codes?
Yes, when triggered by sensor failure. Replacing aged upstream and downstream units resolves heater circuit faults like P0135/P0155 and skewed post-cat readings, though a physically degraded catalytic converter will still trigger P0420/P0430. Clear stored codes after installation and complete a full drive cycle so monitors can run.
Do these sensors require splicing or special installation prep?
No splicing is required. Each sensor features a direct-fit connector matching interchange numbers 234-9012, 234-4149, 234-4516, and 234-9049. Keep grease and anti-seize off the sensing element tip, thread the body in by hand, and torque to factory specification.
The Toyota Precision Standard
Engineered to match OEM telemetry tolerances for the XL20 platform, this matched four-sensor kit restores crisp closed-loop fueling and dependable emissions readiness across both engine banks. Servicing all four positions together prevents mismatched sensor response lag and keeps your 2GR-FE running clean and CEL-free.
Fitment
Fitment
|
Make |
Toyota |
|---|---|
|
Engine Size |
|
|
Year |
|
Warranty
Warranty
All products are backed by our Limited Lifetime Warranty. We stand by our quality. [See terms]

Shopping Safely
At our Shopify store, we prioritize your safety and security. Here's how we ensure a secure shopping experience:
1. Secure Transactions: We use advanced encryption to protect your personal and payment information, ensuring it is safely transmitted and safeguarded.
2. Trusted Payment Gateways: Our store integrates with trusted payment gateways, ensuring your transactions are processed securely and efficiently.
3. Data Privacy: Your privacy is our top priority. We follow strict data protection policies to keep your personal information confidential and secure.
4. Secure Platform: Shopify provides robust security features and continuous monitoring against vulnerabilities, ensuring a safe shopping environment.
5. Verified Merchants: We are a verified merchant on Shopify, committed to providing authentic and high-quality products.
6. Transparent Policies: Our clear return, refund, and shipping policies provide peace of mind, knowing we stand behind our products.
7. Customer Support: Our dedicated customer support team is ready to assist with any concerns or questions you may have.
Shop confidently at our Shopify store, where your safety and satisfaction are our top priorities.
$115.95