Driver Side Exhaust Manifold for Jeep Wrangler (2007-2011) 3.8L
Couldn't load pickup availability
- Guaranteed Fitment
- Free Shipping, Lower 48 States
- Lifetime Warranty
Want it soon? Order within
Shop safely
Secure checkout with trusted payment providers.
Direct-Fit Cast-Iron Driver Side Exhaust Manifold for 2007-2011 Jeep Wrangler (JK)
What it Does: This left-hand cast-iron exhaust manifold channels exhaust gases from the driver-side cylinder head bank to the downpipe on 2007-2011 Jeep Wrangler JK models equipped with the 3.8L EGH V6 engine, restoring leak-free sealing and accurate oxygen sensor feedback.
The Stock Jeep Wrangler Driver-Side Manifold Failure
On the JK Wrangler powered by the 3.8L EGH V6, repeated thermal expansion and contraction cycles create severe stress along the cast-iron runners and cylinder head flange. Over time, extreme heat soak causes the factory left-hand manifold to warp or develop hairline cracks, while factory mounting studs frequently seize or snap inside the cylinder head. Once the flange lifts or the gasket burns out, escaping exhaust pulses draw false air past the seal, skewing O2 readings and triggering lean codes like P0171/P0174.
Common Symptoms of a Failing OEM Driver-Side Exhaust Manifold
- Check Engine Light / Lean DTCs: False air ingestion at a cracked runner or blown flange gasket skews fuel trims and triggers lean codes such as P0171/P0174.
- Cold-Start Ticking & Broken Studs: A distinct metallic ticking noise from the left-hand cylinder head on cold start—often quieting as the casting expands—signals a warped flange, hairline crack, or snapped stud.
- Under-Hood Heat & Component Damage: Unchecked exhaust leaks blow superheated gas across neighboring heat shields and wiring harnesses while increasing cabin noise and risking downpipe joint failure.
The Direct-Fit Cast-Iron Exhaust Manifold Solution
Replacing the compromised factory unit with this OEM-style cast-iron manifold restores structural rigidity and factory exhaust flow geometry on the JK platform. Precision-machined mounting flanges ensure a flat, uniform mating surface against the 3.8L EGH V6 cylinder head to prevent recurring gasket blowouts. The casting comes with an integrated heat shield and exact port and collector clocking for bolt-on downpipe alignment. Supplied with a new gasket, bolts, and washers, it directly replaces 4666024AB, 4666024AC, and 4666024AD.
What's Included
- (1) Driver-side cast-iron exhaust manifold with integrated heat shield
- (1) Exhaust manifold gasket
- (2) Mounting bolts
- (2) Washers
Technical Specifications
| Fitment | 2007-2011 Jeep Wrangler |
|---|---|
| Engine / Chassis | 3.8L EGH V6 / JK |
| Material & Construction | OEM-Style Cast Iron / Integrated Heat Shield |
| Installation Type | Direct Bolt-On OEM Replacement (No Cutting or Welding) |
| Replaces OEM Part # | 4666024AB, 4666024AC, 4666024AD, 674915, 674-915 |
Compatibility
- 2007-2011 Jeep Wrangler (JK) — 3.8L V6 (Driver Side / Left-Hand Only)
Frequently Asked Questions & Fitment Warnings
Does this fit the JK Wrangler?
Yes. This is a direct fit for the 2007-2011 Jeep Wrangler equipped with the 3.8L EGH V6 engine. It fits the driver side (left-hand) only—it does not fit the passenger side, 2012+ 3.6L Wrangler engines, or serve as a full header set.
Will replacing a cracked manifold resolve cold-start ticking and P0171/P0174 lean codes?
Yes, when an exhaust leak is the root cause. Sealing the head-to-manifold flange and eliminating runner cracks prevents false air from entering ahead of the upstream O2 sensor, resolving exhaust-leak-induced P0171/P0174 lean codes and cold-start ticking on the JK.
Are gaskets and mounting hardware included, and what install prep is required?
Yes. The package includes a new manifold gasket, two bolts, and two washers, with the heat shield in place on the casting. Clean the cylinder head flange, start all fasteners by hand so the manifold sits flat, tighten in the 3.8L JK torque sequence, recheck torque after the first heat cycle, and inspect both the head and downpipe joints for leaks.
The Jeep Heavy-Duty Standard
Engineered for trail thermal cycling and sustained towing loads on the JK platform, this cast-iron driver-side manifold restores reliable exhaust sealing without thin-wall header resonance. Confirm port layout, collector clocking, and mounting points against your removed unit before final assembly for a clean, leak-free repair.
Fitment
Fitment
|
Make |
Jeep |
|---|---|
|
Engine Size |
|
|
Year |
|
Warranty
Warranty
All products are backed by our Limited Lifetime Warranty. We stand by our quality. [See terms]

Shopping Safely
At our Shopify store, we prioritize your safety and security. Here's how we ensure a secure shopping experience:
1. Secure Transactions: We use advanced encryption to protect your personal and payment information, ensuring it is safely transmitted and safeguarded.
2. Trusted Payment Gateways: Our store integrates with trusted payment gateways, ensuring your transactions are processed securely and efficiently.
3. Data Privacy: Your privacy is our top priority. We follow strict data protection policies to keep your personal information confidential and secure.
4. Secure Platform: Shopify provides robust security features and continuous monitoring against vulnerabilities, ensuring a safe shopping environment.
5. Verified Merchants: We are a verified merchant on Shopify, committed to providing authentic and high-quality products.
6. Transparent Policies: Our clear return, refund, and shipping policies provide peace of mind, knowing we stand behind our products.
7. Customer Support: Our dedicated customer support team is ready to assist with any concerns or questions you may have.
Shop confidently at our Shopify store, where your safety and satisfaction are our top priorities.
$160.95