Stage 1 Performance Chip for Cadillac - Boost HP & Torque | OBD2 Plug & Play Module

Unlock the "Standard of the World" Performance

Cadillac has set the "Standard of the World" for over a century, pioneering the mass-produced V8 engine and redefining American luxury. From the velvet-smooth power of the classic Northstar engines to the Nürburgring-tuned agility of the modern V-Series, these vehicles are built for power. However, factory tuning often restrains this potential to prioritize ultra-soft shifting and strict fuel economy compliance.

The GTE Stage 1 Performance Chip is designed to unleash the true spirit of your Cadillac. This advanced OBDII module safely optimizes your On-Board Computer to remove the "electronic leash" holding your engine back. It bridges the gap between luxury cruising and the raw performance lurking beneath the hood—installing in minutes without a single tool.

Why Upgrade Your Cadillac with GTE Stage 1?

Whether you are hauling family in an Escalade or carving corners in an ATS, the Stage 1 upgrade revitalizes your driving experience. It overcomes the heavy curb weight of luxury vehicles by delivering power exactly when you need it.

• Revitalized Acceleration: Sharpen 0-60 times and eliminate the hesitation when merging onto freeways.
• Maximize Output: Gain up to +20HP and +19.1 ft·lbs of torque.
• Efficient Cruising: Optimize air/fuel ratios for up to +4 MPG increase—vital for thirsty V8 and Twin-Turbo engines.
• Instant Response: Eliminate "drive-by-wire" throttle lag for up to 50% better response.
• 100% Plug-n-Play: Installs in under 5 minutes inside the cabin. No grease, no mechanic required.

Safe for Advanced Electronics

Modern Cadillacs are technological marvels, equipped with CUE systems and Magnetic Ride Control. You need a tuning solution that respects this architecture. The GTE Stage 1 is a sophisticated microprocessor that communicates safely with the ECU. It optimizes engine parameters without interfering with your infotainment or suspension systems.

Warranty Protected: We understand the value of your investment. This module makes zero permanent modifications. It connects to the OBDII port and can be removed instantly, reverting the car to 100% factory settings. It leaves no digital footprint for the dealer to find, keeping your warranty safe under the Magnuson Moss Warranty Act.

• ✅ Designed and Made in the USA
• ✅ Lifetime Warranty
• ✅ 100% Money-Back Satisfaction Guarantee

Vehicle Compatibility

Our engineers have custom-programmed this module specifically for Cadillac vehicles (1996 - Present). It is fully compatible with Automatic and Manual transmissions.

Supported Models Include:

• SUVs: Escalade (ESV/EXT), SRX, XT4, XT5, XT6, and Lyriq.
• Performance Sedans: CTS, CTS-V, ATS, ATS-V, CT4, CT5, and STS.
• Classic Luxury: DeVille, Seville, DTS, Eldorado, and Fleetwood (1996+).
• Engines: Compatible with Northstar V8, LS/LT V8 (Vortec), 3.6L V6, and 2.0L Turbo engines.

Frequently Asked Questions

Do I need tools to install this?
No. This is a seamless "Plug-n-Play" install. If you can plug in a phone charger, you can install this chip. It utilizes the OBDII diagnostic port typically located under the driver's side dashboard.

Will this work with Active Fuel Management (cylinder deactivation)?
Yes. The GTE Stage 1 works perfectly with V8 models equipped with cylinder deactivation technology (V4/V8 mode). It optimizes power when all cylinders are firing and efficiency when cruising.

Is it safe for the Turbo engines (ATS/CTS/CT4)?
Yes! The module is highly effective on Cadillac's turbocharged engines, optimizing boost delivery and fuel mapping for significant torque gains without compromising engine life.

How long until I see results?
You will likely feel a sharper throttle pedal immediately. Full horsepower and MPG gains typically stabilize after about 100 miles (or 2 weeks) of driving as the ECU adapts to the new optimization map.

Experience the performance your Cadillac was built to deliver. Order risk-free today!