Cold Air Intake for Infiniti M35 Sedan (2006-2008) 3.5L Engine - Red
Couldn't load pickup availability
- Guaranteed Fitment
- Free Shipping, Lower 48 States
- Lifetime Warranty
Want it soon? Order within
Performance Air Intake Kit for Infiniti M35 Sedan 3.5L (2006–2008)
Unlock improved performance and a more engaging driving experience with this Performance Air Intake Kit designed exclusively for the Infiniti M35 Sedan (2006–2008) equipped with the 3.5L V6 engine. Finished in a bold red design, this intake system enhances engine airflow, throttle response, and overall efficiency while maintaining everyday reliability.
The Infiniti M35 is respected for blending luxury refinement with strong V6 performance. This intake kit builds on that foundation by reducing intake restriction, allowing the engine to draw in cooler, denser air for smoother acceleration and stronger power delivery.
Vehicle Fitment
- Infiniti M35 Sedan: 2006–2008
- Engine: 3.5L V6
Fitment Note: Made specifically for 2006–2008 Infiniti M35 Sedan 3.5L V6 models.
Performance Benefits
- Increase horsepower and torque by up to 10%
- Improved throttle response for quicker acceleration
- Enhanced airflow efficiency for smoother engine operation
- Deeper, sportier intake sound under acceleration
- Potential improvement in fuel economy
Premium Construction
- Lightweight aluminum intake piping for durability and heat resistance
- High-flow air filter engineered for exceptional filtration
- Optimized intake routing to maximize airflow through the stock manifold
- Direct replacement for the factory air filter and intake tube
Maintenance & Longevity
- Washable and reusable air filter
- Lower long-term maintenance costs compared to disposable filters
Easy Installation
- Installs with basic hand tools
- No cutting or permanent modifications required
- Average installation time: under 60 minutes
- Consult your dealer about warranty coverage for aftermarket parts.
Installation Tip: After installation, briefly disconnect the battery to allow the ECU to reset and adapt to the increased airflow.
Common Questions
Will this cold air intake fit my 2006–2008 Infiniti M35 Sedan?
Yes, this intake kit is a direct replacement for the 2006, 2007, and 2008 Infiniti M35 Sedan equipped with the 3.5L V6 engine.
Does this fit a 2009 or 2010 Infiniti M35?
This system is built specifically for the 2006–2008 Infiniti M35 Sedan with the 3.5L V6 single-throttle-body engine.
What performance gains can I expect from this intake?
By reducing intake restriction and drawing in cooler, denser air, this kit increases horsepower and torque by up to 10% while sharpening throttle response and adding a sportier intake sound.
Is the air filter washable and reusable?
Yes, the kit comes with a high-flow air filter that is fully washable and reusable, reducing long-term maintenance costs compared to disposable paper filters.
How long does installation take and are modifications required?
Installation takes under 60 minutes using basic hand tools. It is a direct replacement for the factory air filter and intake tube, requiring no cutting or permanent modifications.
Fitment
Fitment
Installation & Tools
Installation & Tools
DIY Guide: Cold Air Intake for Infiniti M35 Sedan (2006-2008) 3.5L Engine - Red for 2006-2008 Infiniti M35 3.5L
Required Tools
- 10mm Socket, Extension, and Ratchet
- 8mm Nut Driver or Flathead Screwdriver (for worm-gear clamps)
- #2 Phillips Screwdriver (for Mass Air Flow sensor screws)
- Needle-Nose Pliers (for factory spring clamps)
When transferring the factory Mass Air Flow (MAF) sensor into the new aluminum adapter housing, never touch the delicate internal sensing wire. Inspect the rubber O-ring at the base of the sensor to ensure it sits flush and does not tear, as even a pinhole vacuum leak after the MAF will trigger a lean fuel trim code on the VQ35DE engine.
Phase 1: Factory Component Removal
- Disconnect the negative battery terminal using a 10mm socket to reset the ECU fuel trims during installation.
- Unplug the electrical harness from the Mass Air Flow (MAF) sensor and unclip the wiring loom from the factory plastic airbox.
- Use needle-nose pliers to slide back the spring clamp on the crankcase breather hose, then detach the hose from the factory intake tube.
- Loosen the clamp at the throttle body, remove the 10mm airbox mounting bolts, and lift the entire OEM intake tube and airbox assembly out of the engine bay.
Phase 2: Aftermarket Installation
- Unscrew the MAF sensor from the OEM housing using a #2 Phillips screwdriver and secure it into the machined boss on the supplied silver aluminum MAF adapter section.
- Slide one red silicone coupler onto the throttle body and attach the main polished aluminum intake pipe, using the second red silicone coupler to join the main pipe to the MAF adapter section. Leave the 8mm worm-gear clamps slightly loose for routing adjustments.
- Fit the high-flow red cone air filter onto the end of the MAF adapter housing and tighten its clamp securely.
- Connect the factory breather hose to the port on the polished intake pipe, tighten all worm-gear clamps, plug the MAF harness back in, and reconnect the negative battery terminal.
Disclaimer: This is a general guide provided for the 2006-2008 Infiniti M35 3.5L. Always refer to your factory service manual for exact torque specifications and safety procedures.
Warranty
Warranty
