Saltar al contenido del producto
1 de 4

O2 Oxygen Sensor Upstream Downstream for Mitsubishi Lancer (2009-2010) 2.4L



Precio regular $53.95
Precio de oferta $53.95 Precio regular
Envío calculado al finalizar la compra.
  • Pago totalmente seguro
  • Con la confianza de miles de personas
  • Calificado y revisado

¿Lo quieres pronto ? Haz tu pedido antes de

I18n Error: Missing interpolation value "end_date" for "Termina el {{ end_date }}"

Direct-Fit Upstream & Downstream O2 Oxygen Sensor Kit for 2009-2010 Mitsubishi Lancer (CY5A)

What it Does: This matched upstream and downstream oxygen sensor kit monitors pre- and post-cat exhaust oxygen on the 2009-2010 Mitsubishi Lancer (CY5A) 4B12 2.4L to maintain accurate fuel trim and verify catalyst efficiency.

The Stock Mitsubishi Lancer Oxygen Sensor Failure

Factory oxygen sensors on the CY5A Lancer equipped with the 4B12 2.4L endure severe thermal cycling and exhaust soot directly downstream of the manifold. Thermal fatigue eventually fractures the internal ceramic sensing element or burns out the heater circuit, causing sluggish voltage switching. Once biased or heater-failed, the ECU loses accurate stoichiometric feedback and triggers codes such as P0135, P0141, or P0171.

Common Symptoms of a Failing OEM Oxygen Sensor

  • Check Engine Light / DTCs: Stored heater or slow-response codes like P0135, P0141, or false catalyst efficiency code P0420.
  • Rough Idle & Hesitation: Biased pre-cat voltage disrupts closed-loop fuel trim and throttle response.
  • Failed Emissions & Fuel Burn: Incomplete OBD-II readiness monitors and higher fuel consumption from open-loop fueling.

The Direct-Fit Heated Zirconia Oxygen Sensor Solution

This two-piece kit replaces both pre-cat and post-cat sensors simultaneously to eliminate signal drift between a fresh unit and a worn partner sensor. Each sensor uses a fast-light-off internal heater, stainless steel housing, and OEM-style connector matching 234-4116 and 234-4114 for direct plug-and-play installation without splicing. Factory thread pitch and harness length ensure clean routing away from exhaust heat on the 4B12 2.4L.

What's Included

  • 1 Upstream Oxygen Sensor
  • 1 Downstream Oxygen Sensor

Technical Specifications

Fitment 2009-2010 Mitsubishi Lancer
Engine / Chassis 4B12 2.4L / CY5A
Emissions & Substrate EPA Federal (46-State Legal) / Heated Zirconia Ceramic Element
Installation Type Direct Bolt-On OEM Replacement (Plug-and-Play, No Splicing)
Replaces OEM Part # 234-4116, 234-4114

Compatibility

  • 2009 Mitsubishi Lancer 2.4L (CY5A)
  • 2010 Mitsubishi Lancer 2.4L (CY5A)

Frequently Asked Questions & Fitment Warnings

Does this fit the CY5A Lancer?

Yes. This is a direct fit for the 2009-2010 Mitsubishi Lancer equipped with the 4B12 2.4L engine. Excluded: 2.0L (4B11) naturally aspirated or turbocharged Evolution/Ralliart trims and other model years.

Will this clear O2 heater or P0420 codes?

Yes, when caused by failed sensors. Replacing both resolves P0135 and P0141 heater faults after clearing codes and completing a drive cycle; a damaged catalytic converter still triggers P0420.

Is wire splicing or special installation prep required?

No splicing is required. Connectors match 234-4116 and 234-4114; keep grease and anti-seize off the sensing tip, hand-thread each body, and torque to factory specification.

The Mitsubishi Precision Standard

Engineered for crisp throttle response and accurate closed-loop fueling on the CY5A platform, this matched sensor set restores factory combustion efficiency. Keep your 4B12 2.4L running CEL-free and emissions-compliant under daily driving and high-RPM load.




Mueble

Hacer

Mitsubishi

Tamaño del motor

  • 2.4L

Año

  • 2009
  • 2010

Garantía

Todos los productos están respaldados por nuestra garantía limitada de por vida. Confiamos en nuestra calidad. [Ver términos y condiciones]

O2 Oxygen Sensor Upstream Downstream for Mitsubishi Lancer (2009-2010) 2.4L

$53.95