Saltar al contenido del producto
1 de 2

O2 Oxygen Sensor Upstream Downstream for Ford Mustang (2011-2014) 5.0L



Precio regular $113.95
Precio de oferta $113.95 Precio regular
Envío calculado al finalizar la compra.
  • Pago totalmente seguro
  • Con la confianza de miles de personas
  • Calificado y revisado

¿Lo quieres pronto ? Haz tu pedido antes de

I18n Error: Missing interpolation value "end_date" for "Termina el {{ end_date }}"

Direct-Fit Upstream & Downstream O2 Oxygen Sensor Kit for 2011-2014 Ford Mustang (S197)

What it Does: This 4-piece upstream and downstream oxygen sensor kit monitors pre- and post-catalytic exhaust oxygen content on the S197 2011–2014 Ford Mustang 5.0L Coyote V8 so the engine control module can regulate air-fuel trim and verify catalytic converter efficiency.

The Stock Ford Mustang O2 Sensor Failure

Factory oxygen sensors on the S197 equipped with the 5.0L Coyote V8 endure severe thermal cycling, exhaust soot, and moisture condensation. Over time, internal heater elements open-circuit and sensing cells become contaminated or slow to respond, causing biased voltage signals and delayed closed-loop fuel trim switching. Replacing only one faulty sensor leaves aged partner sensors on the opposing bank, creating bank-to-bank fueling imbalances and triggering recurring P0135, P0155, P0420, or P0430 diagnostic trouble codes.

Common Symptoms of a Failing OEM Oxygen Sensor

  • Check Engine Light & Heater/Circuit DTCs: Triggered codes such as P0135, P0155, P0141, or P0420/P0430 caused by slow sensor response, biased readings, or internal heater failure.
  • Rough Idle & Throttle Hesitation: Corrupted pre-cat feedback forces the PCM into erratic long-term and short-term fuel trims, causing uneven combustion across cylinder banks.
  • Higher Fuel Consumption & Failed Emissions: Rich default fueling degrades fuel economy, while unresponsive downstream sensors prevent emissions readiness monitors from setting.

The Direct-Fit 4-Piece Oxygen Sensor Solution

This complete 4-sensor kit (interchange 234-5113) services both upstream pre-cat and downstream post-cat positions simultaneously to restore uniform bank-to-bank air-fuel feedback. Each unit features application-matched OEM-style connectors, precision-threaded housings, and fast-acting internal heaters for immediate closed-loop operation without cutting or splicing generic leads. Keep grease and anti-seize off the sensing tip, hand-thread each body into the exhaust bung, torque to factory specification, and complete a drive cycle after clearing codes.

What's Included

  • 2 Upstream (Pre-Catalytic Converter) Oxygen Sensors
  • 2 Downstream (Post-Catalytic Converter) Oxygen Sensors

Technical Specifications

Fitment 2011-2014 Ford Mustang
Engine / Chassis 5.0L Coyote V8 / S197
Stock Engine Output 412–420 hp / 390 lb-ft
Installation Type Direct-Fit OEM Replacement (Plug-and-Play, No Splicing)
Replaces OEM Part # 234-5113

Compatibility

  • 2011-2014 Ford Mustang 5.0L (Confirm engine displacement, model year, and connector style against your vehicle before ordering)

Frequently Asked Questions & Fitment Warnings

Does this fit the S197 Mustang?

Yes. This is a direct fit for the 2011-2014 Ford Mustang equipped with the 5.0L Coyote V8 engine. Excludes 3.7L V6, 5.4L, and 5.8L models as well as other model years even when the body style looks identical; verify connector style before ordering.

Will replacing all four sensors clear O2 and catalyst codes like P0135 or P0420?

Yes, when worn sensors are the root cause. Replacing both upstream and downstream pairs resolves heater circuit and slow-response faults (P0135, P0155, P0141) and restores accurate converter monitoring; clear stored codes and allow a full drive cycle so readiness monitors run.

Do these sensors require wire splicing, and what prep is needed during install?

No splicing is required. Each sensor uses the direct-fit connector for the 5.0L application—keep grease and anti-seize off the sensing element, thread the body in by hand to prevent cross-threading, and tighten to specified torque.

The Ford Performance Standard

Balanced bank-to-bank air-fuel control is essential for crisp throttle response, high-RPM fueling stability, and consistent exhaust efficiency in your S197 Mustang. Refreshing all four sensors together eliminates asymmetric fueling drift and restores factory-grade ECU precision.




Mueble

Hacer

Ford

Tamaño del motor

  • 5.0L

Año

  • 2011
  • 2012
  • 2013
  • 2014

Garantía

Todos los productos están respaldados por nuestra garantía limitada de por vida. Confiamos en nuestra calidad. [Ver términos y condiciones]

O2 Oxygen Sensor Upstream Downstream for Ford Mustang (2011-2014) 5.0L

$113.95