High Output Alternator for Jeep Grand Cherokee (2019-2020) 3.6L
Couldn't load pickup availability
- Guaranteed Fitment
- Free Shipping, Lower 48 States
- Lifetime Warranty
Want it soon? Order within
Shop safely
Secure checkout with trusted payment providers.
350-Amp High Output Alternator for 2019-2020 Jeep Grand Cherokee (WK2)
What it Does: This 350-amp, 12-volt high-output alternator replaces the factory charging unit on the 2019-2020 Jeep Grand Cherokee (WK2) equipped with the 3.6L Pentastar V6 engine to deliver increased electrical current for auxiliary lighting, audio systems, and recovery gear.
The Stock Jeep Grand Cherokee Charging Bottleneck
The factory alternator on the WK2 Grand Cherokee equipped with the 3.6L Pentastar V6 (ERC) struggles when electrical demand exceeds stock parameters. Under heavy accessory loads or prolonged underhood heat soak, the OEM diode rectifier bridge overheats and stator insulation degrades, causing voltage regulation failure. Once internal resistance spikes or brush contact wears down, the PCM logs charging faults like P0562 (System Voltage Low) or P0620 (Generator Control Circuit), leaving the battery chronically undercharged.
Common Symptoms of a Failing OEM Alternator
- Check Engine & Battery Warning Lights: Triggers PCM charging circuit codes such as P0562, P0620, or P2503 when regulated output drops below 13.2V.
- Voltage Drop Under Load: Headlight dimming, sluggish power windows, and auxiliary accessory shutdowns when idling with HVAC and exterior lighting active.
- Hard Starting & Dead Batteries: Insufficient amperage recovery during short trips leads to sulfated battery plates, slow cranking, and erratic ESS operation.
The High-Output Alternator Solution
This brand-new 350-amp, 12-volt replacement—never a remanufactured core—is engineered to replace OEM units including 04801779AG, 4801779AH, 4801779AL, and 421000-0750. Built with heavy-duty internal copper windings, high-temp rectifier diodes, and an integrated voltage regulator, it maintains stable charging output across the RPM band. A factory-installed overdrive pulley maximizes stator speed at idle, while the direct-fit cast housing bolts straight onto the 3.6L Pentastar bracketry using the stock electrical connector.
What's Included
- 1 Complete New 350-Amp High Output Alternator (assembled housing, internal regulator, and windings)
- 1 Pre-Installed Overdrive Pulley
Technical Specifications
| Fitment | 2019-2020 Jeep Grand Cherokee |
|---|---|
| Engine / Chassis | 3.6L Pentastar V6 (ERC) / WK2 |
| Factory Electrical Output | 180 Amps / 12V |
| Installation Type | Direct Bolt-On OEM Replacement (No Cutting or Welding) |
| Replaces OEM Part # | 04801779AG, 4801779AG, 4801779AH, 4801779AL, P04801779AG, RL801779AG, 421000-0750, 421000-0751, 421000-0752 |
Compatibility
- 2019 Jeep Grand Cherokee (3.6L V6 Engine Only)
- 2020 Jeep Grand Cherokee (3.6L V6 Engine Only)
Frequently Asked Questions & Fitment Warnings
Does this fit the WK2 Grand Cherokee?
Yes. This is a direct fit for the 2019-2020 Jeep Grand Cherokee equipped with the 3.6L Pentastar V6 engine. It does not fit hybrid powertrains, V8 displacements, or model years outside 2019-2020—confirm engine size under the hood and compare the pulley and electrical connector before ordering.
Will this clear P0562/P0620 voltage codes, and can I reuse my factory pulley?
Yes, replacing a failing unit restores proper charging voltage to resolve codes like P0562 and P0620, but do not swap the original pulley onto this unit. Removing the pre-installed overdrive pulley reduces output at idle; note that some applications may require a slightly shorter serpentine drive belt if belt slip or squeal occurs.
What wiring upgrades and installation steps are required?
A heavier, fused main charging cable is recommended so the full 350-amp rated capacity can reach the battery without excessive resistance. Disconnect the battery prior to installation, transfer applicable spacers or dust covers only if designed to reuse them, torque mounting bolts to factory specification, and verify charging voltage at the battery with a meter.
The Jeep Heavy-Duty Standard
Engineered to handle high-draw recovery gear, auxiliary lighting, and prolonged thermal stress on the trail or highway, this 350-amp alternator keeps your WK2 electrical system stable under heavy load. Consistent voltage delivery protects sensitive onboard control modules and maintains battery state of charge in demanding operating conditions.
Fitment
Fitment
|
Make |
Jeep |
|---|---|
|
Engine Size |
|
|
Year |
|
Warranty
Warranty
All products are backed by our Limited Lifetime Warranty. We stand by our quality. [See terms]

Shopping Safely
At our Shopify store, we prioritize your safety and security. Here's how we ensure a secure shopping experience:
1. Secure Transactions: We use advanced encryption to protect your personal and payment information, ensuring it is safely transmitted and safeguarded.
2. Trusted Payment Gateways: Our store integrates with trusted payment gateways, ensuring your transactions are processed securely and efficiently.
3. Data Privacy: Your privacy is our top priority. We follow strict data protection policies to keep your personal information confidential and secure.
4. Secure Platform: Shopify provides robust security features and continuous monitoring against vulnerabilities, ensuring a safe shopping environment.
5. Verified Merchants: We are a verified merchant on Shopify, committed to providing authentic and high-quality products.
6. Transparent Policies: Our clear return, refund, and shipping policies provide peace of mind, knowing we stand behind our products.
7. Customer Support: Our dedicated customer support team is ready to assist with any concerns or questions you may have.
Shop confidently at our Shopify store, where your safety and satisfaction are our top priorities.
$370.95